For the 3.2 GHz configuration, see the notes that mention “Processors, 3.2 GHz.” Edit $325.00. (The slots are on the front fan and memory cage on either side of the heatsink cover. $111.05 shipping. Apple Mac Pro (Early 2008) 2 x 2.8 GHz Quad-Core Intel Xeon, 20GB Ram, 1TB HD .
Introduced on January 8, 2008. Using the alcohol pad included with the logic board or processor replacement part, clean off any used thermal grease from the processor and the bottom of the heatsink.Before installing a new or existing heatsink, check that the gasket that surrounds the silver colored coating on the underside of the heatsink is in good condition, as shown in the graphic.
For the 3.2 GHz configuration, see the notes that mention “Processors, 3.2 GHz.”Replacement Note for Card Using One Booster Cable: Be sure to connect the card’s booster cable to the correct auxillary power connector on the logic board.
Specifications. Be extremely careful not to touch the gold pins on the bottom of the processor, as this type of connector is very sensitive to contamination. Once complete you will have a faster computer and a stronger understanding of your Mac Pro.Using a long-handled, magnetized #1 Phillips screwdriver, loosen the four captive screws that mount the memory cage to the logic board.Replacement Note: Make sure all AirPort and Bluetooth antenna wires are out of the way before lowering the fan assembly onto the logic board.Warning: Always shut down the computer before opening it to avoid damaging its internal components or the components you are installing. The DIMMs may be very hot.Warning: The edges of the access panel and the enclosure can be sharp. Core Xeon E5472 x2. Use the instructions that follow as guidelines for DIMM placement: For two DIMMs (standard configuration), install one on the top memory card and one on the bottom card; for four DIMMs – install one pair on the top memory card and one pair on the bottom card; for six DIMMs – install two pairs on the top memory card and one pair on the bottom card; for eight DIMMs – install two pairs on the top memory card and two pairs on the bottom card.When purchasing DIMMs for use in Mac computers, always make sure that the memory vendor conforms to the JEDEC (short for Joint Electron Device Engineering Council) specification. You must release the tabs before you can remove the cover from the enclosure.Wear disposable nitrile or latex glovesIf you are replacing the lower processor heatsink with a new heatsink, install the bumper included in the parts box on the side of the heatsink.After the device is turned on for a few seconds, it is stoppedReplacement Note: Make sure the latch is in the up position before replacing the access panel. Doing so could damage the DIMM.Replacement Note: Also make sure the latch on the inside top left edge of the fan assembly engages with the slot on the inside lip of the enclosureIf you are replacing a booster cable with a new one, disconnect the cable from the card.Additional pairs of 1 GB, 2 GB, or 4 GB FB-DIMMs can be installed in the open DIMM slots.
RAM Type: PC6400 DDR2 ECC. Apple Mac Pro Eight Core 3.0. This guide needs images that better demonstrate how to perform specific actions.Touch the metal PCI access covers on the back of the computer to discharge any static electricity from your body.Remove the cover from the enclosure.Note: To remove the memory cage and fan, you must first slide the fan partway into the cage.
Using a magnetized short-handled or right-angled jeweler’s #1 Phillips screwdriver, carefully remove the two short screws that mount the memory cage to the bottom panel of the enclosure.Lift the heatsink straight up and out of the enclosure.Warning: FB-DIMMs carry heatsinks on either side of the DIMM. This procedure applies to 2.8 GHz and 3.0 GHz configurations of the Mac Pro (Early 2008). It is not managed by iFixit staff.Important: Hold the drive by its sides. Be careful not to touch the printed circuit board on the bottom of the drive.Holding the card by the top corners, gently pull up the card and remove it from its expansion slot.Using your forefinger, reach below the fan and release the latch nearest the logic board.Anyone know the specifications on the captive mounting screws for the heatsink? The MBP you have has roughly the same CPU power to a 2.8 GHz 8 core Mac Pro from 2008.
If you have a new heatsink, follow the NEW Heatsink procedure.Every time you remove a processor, you must replace the thermal grease on the processor heatsink. or Best Offer. VRAM Type: GDDR3 SDRAM. $329.00. )Wait 5 to 10 minutes to allow the computer’s internal components to cool.Replacement Note: Before installing the memory cage and fan, make sure all logic board cables below the cage are out of the way so that the cage sits properly and the cables are not pinched or damaged when you tighten the screws.Open the ejectors on the DIMM slot by pushing them out to the sides, and remove the DIMM from the riser card.DIMMs must be installed as pairs of identical size and type, from the same vendor.